Deer Feeder Acc.

Remote control allows you to start your automatic feeder with the push of a button. Activate from 300 feet away. Compatible with any feeder style or brand. Can be used on single motor automatic fish feeders.  Activate from 300 feet away. Compatible with any feeder style or brand. Can be used on single motor fish feeders. Perfect for use from your tree stand truck or pier. Single Frequency (1 remote will operate multiple feeders - if 2 feeders are close enough, the remote might trig..

Give your feeder a longer life in the field with Moultrie's metal spinner plate and funnel kit. Powder-coated metal funnel and spinner plate for most Moultrie feeders Also compatible with most competing models Wind- and rust-resistant spiner plate protects against corrosion 4 outlets reduce clogs while dispensing the same amount of feed in half the time! ..

Boss Buck 3" slip-on-lids are very practical and though they don't lock they're heavy enough to ensure that wind rain and critters can't get to the feed. Fits most 55 gallon drums. 18 GA Steel - 23 3/4" Diameter ..

Boss Buck one piece spun galvanized steel and built to last! Keeps your feed flowing to the spinner. 20GA Steel 1 15/16" Spout, 1 1/2" long 55 Gallon Measures 22.375" O.D. x 7.75" Deep ..

Fits motor shafts that are 1/4" in diameter. Swing doors swing open when feeder runs and close when feeders stops keeping more feed in the spinner plate/hopper and less on the ground. ..

3" slip-on-lids are very practical and though they don't lock they're heavy enough to ensure that wind rain and critters can't get to the feed. Fits most 30 gallon drums. Inside diameter is about 19.75". ..

This 55 gallon lid includes 2 springs to keep the lid secured to the feeder while in use. Eliminates water standing on top of the lid Makes it easy to open while it holds itself on the side. ..

Holds up to 400 lbs. per set of 3 brackets Complete with back plate and bolts 7/8” square tube legs bent to proper angle for mounting 8’ legs to a 55 gallon drum Set of 3 ..

Boss Buck winches are engineered and built tough to be used in a variety of applications. All gears are heat-treated high carbon SAE 1050 steel. Reel and pinion gear shafts turn on oil-impregnated bearings for smooth operation. Winch frames are embossed for added strength. Zinc plating fights against corrosion. Marine Grade - Designed to withstand years of rigorous use. Gear Ratio: 4.1:1 Diameter of Cable: 4.5mm (a little over 1/8") Length of Cable: Over 28" Ratchet Style: 1-Way Ca..

Heavy Duty steel header system is second to none. We use nothing but the best components to build this product. Features our 1,000lb. pulley used on our Hanging Feeder Tripod Systems and Game Skinning Racks . By combining the pulley INCLUDED on the unit with the pulley on your hanging bail, you effectively cut the weight load in HALF. This keeps the winch from free spooling and falling to the ground under load. This also reduces the load on the legs and cable. This block and tackle style system ..

Keep your feeder from sinking in the mud with Boss Buck's metal foot pads. Boss Buck's foot pads are heavy duty 6" square, 1/8" thick steel plates. Complete with a 3/4" stake hole. The stake hole goes to the outside of the feeder and accepts up to 1/2" rebar stakes. Sold Individually. ..

The Boss Buck Non-Typical foot design is completely unique! The feet are designed to accept a T-Post through the center of the foot. The feet are large square steel plates. Each foot has a large nut welded to it and a bolt that when tightened secures the feeder to the T-Post. This will not only protect the feeder but keep it level and immobile. Feet will receive any pipe or tubing with an I.D. of 1.25" or larger. The Square tubing on the Deluxe feet is 7/8" square tubing. Sold Individually..

Boss Buck heavy-duty 2" steel pulley - 1000 lb capacity. 7/32" maximum cable size. Great heavy-duty pulley for building your own hanging feeder and game skinning racks.      ..

Solidly constructed steel spout delivers the feed material to the slinger. Super easy to install. Includes mounting screws. Simply cut a hole in the bottom of any drum. Center spout over the hole and attach screws. GREAT replacement for plastic parts on other manufacturers feeders! Length of the downspout is 2 1/4". Width of mouth is 2 3/8".   ..

12 Volt PM DC 1/4in. x 1in. Shaft 1/35 Horsepower RPM 2942 @ 2 amps Draws 4½ amps at startup, 3 when running Mounting studs are 10/32in X 5/8in. long and are 2.36in. apart Dimensions approximately: 3in. Wide x 3in. Tall 2 3/8in. between two bolts on top of motor ..

Deluxe folding varmint / coon cage. Latching sides drop down allowing easy access to your timer and battery. Comes complete with mounting brackets 7 self-tapping screws. Dimensions: 14" x 14" x 14" Varmint Cage Only Feeder Sold Separately ..

Build your own feeder with any 55 gallon drum, plastic or metal with the Boss Buck Barrel Band system. Easily installs in minutes around the bottom of the barrel. The welded tab supports help position , and support the drum inside the band system. Our band system allows you to mount the feeder legs without drilling holes in the drum. This causes moisture problems over time. The square tubing legs except pipe from 1 1/4″ID and larger. For professional results on your home made feeder use Boss Buc..

All metal hanging bail attaches easily to a 55 gallon barrel to use with a tripod or winch feeder setup. Includes a winch pulley. Painted and sealed to prevent rust.  Dimensions: 22 1/16" I.D. x 17 13/16" Tall ..

Now you can ensure that every last little bit of feed is consumed, thanks to this durable plastic funnel. A simple yet smart solution, the Moultrie internal funnel saves you time and money by dispensing all loaded feed, with no loss and no time spent scraping down the inside.       Prevents feed from being left on the bottom of feeder barrel     Internal drum dispenses all feed without any loss     Compatible with 30-gallon metal barrels only      The diameter of this funnel is 18..

Ideal for the quick and easy refilling of deer feeders, Moultrie’s 30-Gallon Quick Lid is now easier to remove than ever! Still staying on securely when you need it to, the Quick Lid features an indentation that accommodates a solar panel (sold separately) while shedding water. Much more user-friendly than a lid-and-ring solution, this durable feeder barrel lid is made to fit tightly on Moultrie 30-gallon metal feeder barrels and also works with most competing-brand 30-gallon barrels.   ..